GP2Y1010AU0F detects particles in the air by optical sensing.Properties:-Operates on 5 Volt-Current dissapation of less than 20 mA-0-0.6 mg/m3(cubic meter) range-Enable to distinguish smoke from house dust
An infrared emiiting diode and a phototransistor are diagonally arranged. Light reflects on the particles passing through the whole are picked up by the photodiode(PD) is transformed into voltage. The voltage has to be amplified to be able to read the change. You can change the resistance of the RS(variable resistor) in the amplifier circuit to make it more sensitive but if you do so, note that you can't reference output voltage vs. dust sensity at fig.3 (below)
![]() | ![]() |
Image byShinyei | GP2Y1010AU Internal Schematic |
These results are true only when the sensor is used with factory settings. The variable resistor shouldn't be changed.Attach:output.jpg ΔThe table demonstrates that for every 0.1 mg more of dust, the voltage increases by 0.5 Volts.There are other environmental sensors in the market that can detect particles with the size of 1 micrometer (1μm). This scale means that even pollen grains, and mildew spores can be detected. There is no information about this on GP2Y1010AU's datasheet except that it is stated that it can detect cigarette smoke.0.6 mg/m3 of dust doesn't seem much when National Institute for Occupational Safety and Health (NIOSH)'s recommended wood dust is 1 mg/m3 and used to be 5mg/m3 for softwoods.
Applications-Air purifier-Air monitor for industry-Device dust alert-Fire Alarm (although Sharp Electroics wants to be informed if used in such system.)More unusual apps:-Vacuum cleaner robotas inthis guy's paper
Setup and CodeSetup is very straight-forward except the soldering. 6 pin connector header is small and very closed. I had to break one side of the header housing.One important thing about the code is in order to turn the ILED on, you have to digitalWrite LOW on LED input terminal. Because the transistor that opens the drain is PNP type of transistor which needs negative base voltage.I also added a buzzer which goes off when it detects smoke.
Arduino codeProcessing Visualization
In most of these tests, I had watch if the smoke/dust went inside the whole.Test1: Putting off a match
![]() | ![]() |
Test2: Cigarette Smoke
![]() | ![]() |
Test3: Burning Paper
![]() | ![]() |
Test4: Dust from my Rug
![]() | ![]() |
I was confused with the results because I wasn't expecting such high values from the 4th test where i just had some dust falling from my rug. Ok, i admit my rug hasn't been washed for a while but the voltage should only go up when the density is high, and compared to smoke, dust wasn't dense at all.
參數: | |
· | 物鏡:10×消色差 |
· | 目鏡:20×帶0.1mm格值分劃板 |
· | 測量承座:Φ25×10mm |
90°剝離試驗機應用領域:90度電動剝離試驗機專門用于實驗PC板上銅箔電路之附力,或錫箔、銅箔、膠布...等,粘著干物體表面之牢度。試驗時以垂直之角度剝離試料,剝離運行速度可調,測得實際粘結之強度。設有微動開關,能任意設定剝離行程。
90°剝離試驗機產品相冊:
90°剝離試驗機參數規格
1. 測試角度:90°
2. 測試荷重:0—50kg
3. 速度:5—100mm/分
4. 測試行程:350mm
5. 重量:約40kg
6. 電源:AC220V,2A
7. 體積:約660*340*670mm
8. 數顯式推拉力計: 最大拉力50KG
90°剝離試驗機產品特點:
1、專為垂直剝離測試設計制作,設計合理,結構緊固,運行安全、穩定、精確;
2、電動式操作,梯型螺桿傳動,結構牢固,運行穩定,無噪音;
3、試驗速度可調,具有限位裝置,可自動停止運行;
4、可選配數顯/指針推拉力表及各類工裝夾具,測試范圍廣泛。
90°剝離試驗機使用方法
1.使用前必須放在穩固的臺面上,
2.不允許在使用過程中搬弄機臺;
3.選擇相應電源電壓,切勿過高,避免燒壞器件;
4.在儀器出現異常時,請與本所聯系以便及時處理;
5.機器工作時必須有良好的通風環境。
6.按鍵機械各組件,由于運轉負荷較大,機械部分請及時加潤滑油;
7.每次試驗完畢,清理機臺,保持機臺清潔;
8.控制箱部分,須以干布擦拭,不可用濕布。
廈門德儀設備有限公司專業生產的環境試驗設備主要適用于:塑膠橡膠、紙品、包裝、印刷、膠粘帶、五金電子、玩具、家俱、鞋類、嬰兒用品等眾多行業。并且適用于各種科研單位、質檢機構、研究所、高校學術探討等各大領域。公司主要研發、制造和銷售的環境試驗設備有:高低溫交變濕熱試驗箱、高低溫交變試驗箱、高低溫箱、恒溫恒濕試驗箱、步入式恒溫恒濕室、換氣式老化箱、冷熱沖擊試驗箱、紫外線老化箱、氙燈老化試驗箱、臭氧老化箱、鹽霧試驗箱、淋雨試驗箱、砂塵試驗箱、耐黃變試驗箱、超低濕常溫干燥箱、電子防潮柜,低溫低濕干燥箱、真空干燥箱、電熱鼓風干燥箱、跌落試驗機、調頻掃頻振動試驗臺、拉力試驗機等環境試驗設備。產品完全符合UL、ASTM、JIS、GB、ISO、TAPPI、EN、DIN、BS……等國際標準。
RK2681A型絕緣電阻測試儀
主要技術指標:電阻測試范圍:100KΩ~10TΩ測試度: R<1GΩ:3%讀數+0.5格 ≥1GΩ:5%讀數+0.5格 ≥1TΩ:10%讀數+0.5格測試電壓: 10V/50V/100V 250V/500V/1000V電壓度:2%測量電流范圍:≤100UA控制方式:模擬電路觸發方式:無量程方式:手動測試速度:阻性元件:<0.5秒容性元件:0.5~1.0秒分選:合格,不合格及不合格訊響(可開關)
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||